Template:Convert/doc

Template {{convert}} calculates measurements from one unit (you can enter) to another one, and then presents the results. For example:

{{convert|2|km|mi}} → 2 kilometres (1.2 mi)

{{convert|7|mi|km}} → 7 miles (11 km)

The available units are listed below. Multiple formatting and calculation options are listed below.

See also Help:Convert for more complete information

Unit name or symbol (abbreviation): 1 pound or 1 lb?

By default, the first value shows unit name, the second the symbols (= abbreviation). Use |abbr=on/off to change this behaviour:

{{convert|1|lb|kg}} → 1 pound (0.45 kg) (To compare; default: first value shows unit name)

{{convert|1|lb|kg|abbr=on}} → 1 lb (0.45 kg)

{{convert|1|lb|kg|abbr=off}} → 1 pound (0.45 kilograms)

• |abbr=in toggles the default behaviour (|abbr=out):

{{convert|1|lb|kg|abbr=in}} → 1 lb (0.45 kilograms)

Adjective: a 10-mile distance

Use |adj=on to produce the adjective form. The difference:

{{convert|10|mi|km}} to go → 10 miles (16 km) to go. (To compare, default)

A {{convert|10|mi|km|adj=on}} distance → A 10-mile (16 km) distance. (Adjective form)

Rounding: 100 ft is 30 m or 30.5 m or 30.48 m?

In detail, it is 100 feet (30,480 mm). In practical use, it is common to round the calculated metric number. With that, there are several possibilities.

Default rounding

By default, the conversion result will be rounded either to precision comparable to that of the input value (the number of digits after the decimal point—or the negative of the number of non-significant zeroes before the point—is increased by one if the conversion is a multiplication by a number between 0.02 and 0.2, remains the same if the factor is between 0.2 and 2, is decreased by 1 if it is between 2 and 20, and so on) or to two significant figures, whichever is more precise. An exception to this is rounding temperatures (see below).

Examples of rounding
Input	Displays as	Note
{{convert|123|ft|m|-1}}	123 feet (40 m)
{{convert|123|ft|m|0}}	123 feet (37 m)
{{convert|123|ft|m|1}}	123 feet (37.5 m)
{{convert|550|ft|m|0}}	550 feet (168 m)	Approximate value is 167.64 m
{{convert|550|ft|m}}	550 feet (170 m)	Rounds to 170, when approximate value is 167.64 m
{{convert|500|ft|m|0}}	500 feet (152 m)	Approximate value is 152.4 m
{{convert|500|ft|m}}	500 feet (150 m)	Rounds to 150, when approximate value is 152.4 m

Convert supports four types of rounding:

Round to a given precision: use |precision=

Specify the desired precision with the fourth unnamed parameter (or third unnamed parameter if the "convert to" parameter is omitted; or fifth unnamed parameter if a range is specified; or fourth unnamed parameter again if a range is specified and the "convert to" parameter is omitted; needs to be replaced with a "precision" named parameter). The conversion is rounded off to the nearest power of ​¹⁄₁₀ this number. For instance, if the result is 8621 and the round number is "-2", the result will be 8600. If the result is "234.0283043" and the round number is "0", the result will be 234.

Round to a given number of significant figures: use |sigfig=

To specify the output number to be with n significant figures use |sigfig=<number>:

• To compare: {{convert|1200|ft|m}} → 1,200 feet (370 m)
• {{convert|1200|ft|m|sigfig=4}} → 1,200 feet (365.8 m)
• {{convert|1200|ft|m|sigfig=3}} → 1,200 feet (366 m)
• {{convert|1200|ft|m|sigfig=2}} → 1,200 feet (370 m)
• {{convert|1200|ft|m|sigfig=1}} → 1,200 feet (400 m)

Setting |sigfig= is meaningless

• {{convert|1200|ft|m|sigfig=0}} → 1,200 feet (370 m)

Round to a multiple of 5: 15, 20, 25, ...

Using |round=5 rounds the outcome to a multiple of 5.

{{convert|10|m|ft}} → 10 metres (33 ft)

{{convert|10|m|ft|round=5}} → 10 metres (35 ft)

Similar: using |round=25 rounds the outcome to a multiple of 25.

{{convert|10|m|ft}} → 10 metres (33 ft)

{{convert|10|m|ft|round=25}} → 10 metres (25 ft)

To compare: {{convert|10|m|ft|sigfig=4}} → 10 metres (32.81 ft)

In a range, one can round each value individually to the default. Use |round=each:

{{convert|10 x 200 x 3000|m|ft}} → 10 by 200 by 3,000 metres (33 ft × 656 ft × 9,843 ft)

{{convert|10 x 200 x 3000|m|ft|round=each}} → 10 by 200 by 3,000 metres (33 ft × 660 ft × 9,800 ft)

Round to a multiple of a given fraction: ​2 ³⁄₁₆ inch

Specify the desired denominator using |frac=<some positive integer>. (Denominator is the below-the-slash number, for example the 3 in ​¹⁄₃).

{{convert|5.56|cm|in|frac=16}} → 5.56 centimetres (2+3⁄16 in)

{{convert|8|cm|in|frac=4}} → 8 centimetres (3+1⁄4 in)

The fraction is reduced when possible:

{{convert|8|cm|in|frac=100}} → 8 centimetres (3+3⁄20 in)

{{convert|8|cm|in}} → 8 centimetres (3.150 in) (To compare)

Rounding the temperatures °C, °F and K

In temperatures, the conversion will be rounded either to precision comparable to that of the input value or to that which would give three significant figures when expressed in kelvins, whichever is more precise.

{{convert|10|C|F K}} → 10 °C (50 °F; 283 K)

Note

For a temperature difference, like to convert "A rise of 20 °C", use |C-change=20 &tc.

{{convert|20|C-change|F-change K-change}} → A rise of 20 °C (36 °F; 20 K)

To compare: "A temperature of 20 °C" would yield: A temperature of 20 °C (68 °F; 293 K)

Into multiple units: 10 °C (50 °F; 283 K)

Separate the multiple output units by a space:

{{convert|10|C|F K}} → 10 °C (50 °F; 283 K)

{{convert|5|km|mi nmi}} → 5 kilometres (3.1 mi; 2.7 nmi)

Ranges of values

A range: 6 to 17 kg (13 to 37 lb)

Range indicators are entered as the second parameter (between the values). Range separators can be:

Range separators in {{convert}}
Separator	Convert	Result	Notes
-	{{convert|3|-|6|ft}}	3–6 feet (0.91–1.83 m)	Input can be hyphen (-) or en dash (–), output uses en dash
– – (en dash)	{{convert|3|–|6|ft}}	3–6 feet (0.91–1.83 m)
and	{{convert|3|and|6|ft}}	3 and 6 feet (0.91 and 1.83 m)
and(-)	{{convert|3|and(-)|6|ft}}	3 and 6 feet (0.91–1.83 m)	|abbr=on abbreviates the first unit
and(-)|abbr=on	{{convert|3|and(-)|6|ft|abbr=on}}	3 and 6 ft (0.91–1.83 m)
or	{{convert|3|or|6|ft}}	3 or 6 feet (0.91 or 1.83 m)
to	{{convert|3|to|6|ft}}	3 to 6 feet (0.91 to 1.83 m)
to(-)	{{convert|3|to(-)|6|ft}}	3 to 6 feet (0.91–1.83 m)	|abbr=on abbreviates the first unit
to(-)|abbr=on	{{convert|3|to(-)|6|ft|abbr=on}}	3 to 6 ft (0.91–1.83 m)
to about	{{convert|3|to about|6|ft}}	3 to about 6 feet (0.91 to about 1.83 m)
+/-	{{convert|3|+/-|6|ft}}	3 ± 6 feet (0.91 ± 1.83 m)
± ±	{{convert|3|±|6|ft}}	3 ± 6 feet (0.91 ± 1.83 m)
+	{{convert|3|+|6|ft}}	3 + 6 feet (0.91 + 1.83 m)
,	{{convert|3|,|6|ft}}	3, 6 feet (0.91, 1.83 m)
, and	{{convert|3|, and|6|ft}}	3, and 6 feet (0.91, and 1.83 m)
, or	{{convert|3|, or|6|ft}}	3, or 6 feet (0.91, or 1.83 m)
by	{{convert|3|by|6|ft}}	3 by 6 feet (0.91 by 1.83 m)
x	{{convert|3|x|6|ft}}	3 by 6 feet (0.91 m × 1.83 m)	|abbr=on abbreviates and repeats the first unit
× ×	{{convert|3|×|6|ft}}	3 by 6 feet (0.91 m × 1.83 m)
x|abbr=on	{{convert|3|x|6|ft|abbr=on}}	3 ft × 6 ft (0.91 m × 1.83 m)
xx	|xx| is deprecated. Use |x| instead
*	|*| is deprecated. Use |x| instead

Multiple dimensions: 6 m × 12 m (20 ft × 39 ft)

Use "by"

{{convert|6|by|12|ft|m}} → 6 by 12 feet (1.8 by 3.7 m)

Use "×" or ""x""

{{convert|6|x|12|m|ft}} → 6 by 12 metres (20 ft × 39 ft)

In science, the formal way is to set |x| and |abbr=on (keeping dimensions right, like in area = x km²):

{{convert|6|x|12|m|ft|abbr=on}} → 6 m × 12 m (20 ft × 39 ft)

About feet, inch in ranges and multiples

While it is possible to enter feet, inch in a simple conversion, this is not possible for ranges:

• {{convert|1|ft|3|in|mm}} → 1 foot 3 inches (380 mm) (to compare)
• {{convert|1|ft|3|in|x|3|ft|5|in|mm}} → 1 foot 3 inches ()

Words

Spell out numbers: ten miles

To write a number in words, use |spell=in:

{{convert|10|mi|m|spell=in}} → ten miles (16,000 m)

To spell out both in and out values, use |spell=on:

{{convert|10|mi|m|spell=on}} → ten miles (sixteen thousand metres)

To make first letter a capital, use |spell=In, |spell=On

{{convert|10|mi|m|spell=In}} → Ten miles (16,000 m)

{{convert|10|mi|m|spell=On}} → Ten miles (sixteen thousand metres)

Remember that the spelling of the units (ft, m) is independently set by |abbr=. To the extreme:

{{convert|10|mi|m|spell=on|abbr=off|sp=us}} → ten miles (sixteen thousand meters)

Spelling of units: UK metre or US meter?

Default spelling of units is en-UK. To show en-US spelling, use |sp=us:

{{convert|1|m|ft}} → 1 metre (3.3 ft) -- default

{{convert|1|m|ft|sp=us}} → 1 meter (3.3 ft)

Extra words: 4 planted acres

Incomplete section

{{convert|4|acre||adj=pre|planted}} → 4 planted acres (1.6 ha)

Extra adjective words: A 10-foot-long corridor

{{convert|4|ft|m|adj=mid|-long}} → 10-foot-long (3.0 m)

Grammatical construction: The 18-, 24- and 32-pounder (8, 11 and 15 kg) cannons

This example is from article Fort McHenry:

The American defenders had 18-, 24- and 32-pounder (8, 11 and 15 kg) cannons.

This formatted result is not possible straightforward by using {{convert}}. However, it can be made in three steps.

Step 1: Enter the input numbers and units in {{convert}} just to get the calculated output:

• had {{convert|18 |, |24 |, |32 |lb |kg |0 }} cannons

→ had 18, 24, 32 pounds (8, 11, 15 kg) cannons

The core conversion should look good now. You can save this (or preview).

Step 2: We need the resulting text in plain code in the page, not as a {{convert|...}} template.

For this, add subst: to the template name (for 'substitute') :

• had {{Template:Purpleconvert|18 |, |24 |, |32 |lb |kg |0 }} cannons

As a check: the preview result should show the conversion correct, with the numbers still right.

Now save this.

→ had 18, 24, 32 pounds (8, 11, 15 kg) cannons

Step 3: When opening the edit screen again, you'll see that the text is there in code. The template {{convert|...}} itself has disappeared. You can change the text as needed. The edit screen text is:

had 18, 24, 32 pounds (8, 11, 15 kg) cannons

You can edit this text to add the grammar:

• had 18-,_24-_and_32-pounder (8, 11_and_15 kg) cannons

After saving your edit, it shows:

→ "had 18-, 24- and 32-pounder (8, 11 and 15 kg) cannons".

Numbers

Using an SI prefix: gigameter (Gm), or micrometer (μm)

Template:Sidebar metric prefixes (small) Units can have SI prefixes like: G, k, m, μ for giga-, kilo-, milli-, micro- multiplication factors. The symbol (letter) is added to the unit, the word is added to the name: Gm and gigameter.

To illustrate, these are trivial calculations (from meter to meter), displaying the multiplication factor:

• 12 Gm (1.2×10¹⁰ m)
• 12 μm (1.2×10⁻⁵ m)

The prefix can be added before an SI unit (here: unit m for meter):

• {{convert|12|Gm|mi|abbr=on}} → 12 Gm (7,500,000 mi)
• Mm: 12 Mm (7,500 mi)
• km: 12 km (39,000 ft)
• mm: 12 mm (0.47 in)
• μm: 12 μm (0.012 mm)
• um: 12 μm (0.012 mm) (letter "u" can be used for "μ" here)

The prefix can be used in the output unit:

• {{convert|12000|mi||Mm|abbr=on}} → 12,000 mi (19 Mm)
• {{convert|12|in|μm|abbr=on}} → 12 in (300,000 μm)

As an exception, the non-SI unit inch can have the "μ" prefix too)

• {{convert|12|μm|μin|abbr=on}} → 12 μm (470 μin)

Further information: Help:Convert units § SI prefixes

Input with fractions: 1+1⁄2 inches (38.1 mm)

The number to convert can be written in fractions:

{{convert|1/2|in|mm|1}} → 1⁄2 inch (12.7 mm)

Also the fraction slash (⁄) is accepted:

{{convert|1⁄2|in|mm|1}} → 1⁄2 inch (12.7 mm)

With integers, use a + sign

{{convert|2+1⁄2|in|mm|1}} → 2+1⁄2 inches (63.5 mm)

When negative, use a hyphen - and repeat it:

{{convert|-2-1⁄2|in|mm|1}} → −2+1⁄2 inches (−63.5 mm)

{{convert|2-1⁄2|in|mm|1}} → 2–1⁄2 inch (50.8–12.7 mm) Note: this is read as a range

{{convert|-2+1⁄2|in|mm|1}} → N Should be a number, not an expression (do not require a calculation)

Engineering notation: 7 × 10⁶ m

Engineering number notations like 7E6 (for 7 × 10⁶) are to be entered as a prefix en to the unit:

{{convert|7|e6m}} → 7 million metres (23,000,000 ft)

The same is possible for the output unit:

{{convert|23,000,000|ft|e6m}} → 23,000,000 feet (7.0×10^⁶ m)

Any standard unit (not a combination, multiple, or built-in) can have a prefix:

e3 (thousand), e6 (million), e9 (billion), e12 (trillion), e15 (quadrillion).

Thousands separator: 1,000 mi and 1000 mi

In input, a comma for thousands separator is accepted. A gap (space) is not. In output, by default, the thousand separator is the comma:

• {{convert|1,234,567|m|ft}} → 1,234,567 metres (4,050,417 ft)
• {{convert|1,234,567|m|ft}} → 1,234,567 metres (4,050,417 ft)
• {{convert|1 234 567|m|ft}} → N

Set |comma=off to remove the separator:

• {{convert|1234567|m|ft|comma=off}} → 1,234,567 metres (4,050,417 ft)

Use |comma=gaps to set digit grouping by gap (<space>) in larger numbers (thousands separator):

• {{convert|1234567|m|ft}} → 1,234,567 metres (4,050,417 ft) (To compare, default)
• {{convert|1234567|m|ft|comma=gaps}} → 1234567 metres (4050417 ft)

Setting |comma=5 or |comma=gaps5 will only add the separator when the number of digits is 5 or more:

• {{convert|1234|m|ft}} → 1,234 metres (4,049 ft) (To compare, default)
• {{convert|1234|m|ft|comma=5}} → 1234 metres (4049 ft)
• {{convert|1234567|m|ft|comma=5}} → 1,234,567 metres (4,050,417 ft)
• {{convert|1234|m|ft|comma=gaps5}} → 1,234 metres (4,049 ft)
• {{convert|1234567|m|ft|comma=gaps5}} → 1,234,567 metres (4,050,417 ft)

Output with horizontal fraction bar in: 1/2 inch

Using a double slash (//) returns a horizontal bar fraction:

• {{convert|1//2|in|mm|1}} → 1/2 inch (12.7 mm)
• {{convert|2+1//2|in|mm|1}} → 2+1/2 inches (63.5 mm)

Output manipulation

Brackets and separators: 10 m [33 ft]

Punctuation that distinguishes the two measurements is set by |disp=.
Options are: b (the default), sqbr, comma, or, br, x|...:

{{convert|10|m|ft}} → 10 metres (33 ft) -- ( ) brackets are the default

{{convert|10|m|ft|disp=sqbr}} → 10 metres [33 ft]

{{convert|10|m|ft|disp=comma}} → 10 metres, 33 ft

{{convert|10|m|ft|disp=or}} → 10 metres or 33 feet

Setting |disp=br will force a new line (<br>)

{{convert|10|m|ft|disp=br}} → 10 metres
33 feet

Setting |disp=x|... allows any text as separator:

{{convert|10|m|ft|disp=x|_MyText_}} → 10 metres_MyText_33 ft -- (To display spaces, use  )

Flipping (reordering) the two measurements: 1,609.3 metres (1 mile)

Setting |order=flip will flip (swap) the two measurements:

{{convert|1|mi|m}} → 1 mile (1,609.3 metres) (To compare, default)

{{convert|1|mi|m|order=flip}} → 1,609.3 metres (1 mile)

When converting to multiple units, the effect is:

{{convert|10|km|mi nmi|order=flip}} → 6.2137 miles; 5.3996 nautical miles (10 kilometres)

{{convert|10|km|nmi mi|order=flip}} → 5.3996 nautical miles; 6.2137 miles (10 kilometres)

Displaying parts of the result: 2 (1.5)

It is possible to display only parts of the conversion result:

Convert	Output	Description
{{convert|2|cuyd|m3}}	2 cubic yards (1.5 m3)	Default, to compare
{{convert|2|cuyd|m3|abbr=values}}	2 (1.5)	Input and output numbers
{{convert|2|cuyd|m3|disp=unit}}	cubic yards	Input unit
{{convert|2|cuyd|m3|disp=unit|adj=on}}	cubic-yard	Input unit, adjective (hyphenated)
{{convert|2|cuyd|cuyd|0|disp=out|abbr=off}}	2 cubic yards	Input (workaround)
{{convert|2|cuyd|m3|disp=unit2}}	m3	Output unit (symbol)
{{convert|2|cuyd|m3|disp=unit2|abbr=off}}	cubic metres	Output unit (name)
{{convert|2|cuyd|m3|disp=number}}	1.5	Output value
{{convert|2|cuyd|m3|disp=out}}	1.5 m3	Output value and unit
{{convert|2|cuyd|m3|disp=out|abbr=off}}	2 cubic yards (1.5 m3)	Output value and unit

Table options

For the wikitable structure, there are two options: split over columns and make the table sortable.

Show numbers only in columns in a table

Using {convert} in a table cell, with |disp=table splits the result over two columns:

{{convert|10|m|ft|disp=table}} → style="text-align:right;"|10

|style="text-align:right;"|33

|disp=tablecen does the same, and also centers the text:

{{convert|20|m|ft|disp=tablecen}} → style="text-align:center;"|20

|style="text-align:center;"|66

The units are added as a column header:

	m	ft
|disp=table	10	33
|disp=tablecen	20	66
|disp=<other> (default)	30 metres (98 ft)

Sorting

Use both |disp=table |sortable=on to produce table columns (pipe symbols), with sortable table column. As of January 2013, only the first (lefthand) column will sort (improvements pending).

{{convert|10|m|ft|disp=table|sortable=on}} →

style="text-align:right;" data-sort-value="7001100000000000000"|10 |style="text-align:right;" data-sort-value="7001100000000000000"|33

This shows the hidden numerical sortkey:

align="right"|<span style="display:none">7001100000000000000</span>10 |align="right"|33

m	ft
15+3⁄4	52
15.5	51
16.0	52.5
16	52

Units

The table below lists units supported by {{convert}}. More complete lists are linked for each dimension. For a complete list of all dimensions, see full list of units.

{{Convert}} uses unit-codes, which are similar to, but not necessarily exactly the same as, the usual written abbreviation for a given unit. These unit-codes are displayed in column 3 of the following tables. These are accepted as input by {{convert}} as the second and third unnamed parameters:

• {{convert|100|kg|lb}} → 100 kilograms (220 lb)
• {{convert|100|lb|kg}} → 100 pounds (45 kg)

The unit-codes should be treated as case-sensitive:

• {{convert|100|Mm|mm}} → 100 megametres (1.0×10¹¹ mm)

The output of {{convert}} can display multiple converted units, if further unit-codes are specified after the second unnamed parameter (without the pipe separator). Typical combination output units are listed below in column 7.

• {{convert|55|nmi|km mi}} → 55 nautical miles (102 km; 63 mi)
• {{convert|1|oz|ozt g gr}} → 1 ounce (0.91 ozt; 28 g; 440 gr)

Some units have alternative unit-codes. These are shown in brackets in column 3, e.g. °F (F). Either may be entered for Fahrenheit (but not a lower-case f).

Abridged list of supported units
Explanation
system	unit	unit- code		symbol or abbrev.	notes	sample default conversion	combination output units
the system(s) to which the unit belongs	units listed by name	unit-code to use in template		symbols shown in output	other notes about the units	sample of the default conversion for the unit	output codes for multiple conversions
AREA (Full list)
system	unit	unit- code		abbrev- iation	notes	sample default conversion	combination output units
SI	square kilometre	km2		km2	US spelling: square kilometer	1.0 km2 (0.39 sq mi)	km2 sqmi
	square metre	m2		m2	US spelling: square meter	1.0 m2 (11 sq ft)	m2 sqft
	square centimetre	cm2		cm2	US spelling: square centimeter	1.0 cm2 (0.16 sq in)	cm2 sqin
	square millimetre	mm2		mm2	US spelling: square millimeter	1.0 mm2 (0.0016 sq in)	mm2 sqin
non-SI metric	hectare	ha		ha		1.0 ha (2.5 acres)
Imperial & US customary	square mile	sqmi		sq mi		1.0 sq mi (2.6 km2)	sqmi km2
	acre	acre		(none)		1.0 acre (0.40 ha)
	square yard	sqyd		sq yd		1.0 sq yd (0.84 m2)
	square foot	sqft (sqfoot)		sq ft	long code "sqfoot" outputs square foot (and never feet)	1.0 sq ft (0.093 m2)	sqft m2 (sqfoot m2)
	square inch	sqin		sq in		1.0 sq in (6.5 cm2)	sqin cm2
Other	square nautical mile	sqnmi		sq nmi		1.0 sq nmi (3.4 km2; 1.3 sq mi)
	dunam	dunam		(none)	For alternative spellings and definitions see the full list	1.0 dunam (0.0010 km2; 0.00039 sq mi)
	tsubo	tsubo		(none)		1.0 tsubo (3.3 m2)
DENSITY
system	unit	unit- code		abbrev- iation	notes	sample default conversion	combination output units
Metric	kilogram per cubic metre	kg/m3		kg/m3		1.0 kg/m3 (1.7 lb/cu yd)	kg/m3 lb/ft3 (kg/m3 lb/cuft) kg/m3 lb/yd3 (kg/m3 lb/cuyd)
	gram per cubic metre	g/m3		g/m3		1.0 g/m3 (0.0017 lb/cu yd)	g/m3 kg/m3 g/m3 lb/ft3 (g/cm3 lb/cuft) g/m3 lb/yd3 (g/cm3 lb/cuyd)
Imperial & US customary	pound per cubic foot	lb/ft3		lb/cu ft		1.0 lb/cu ft (0.016 g/cm3)	lb/ft3 kg/m3 (lb/cu ft g/m3) lb/ft3 g/m3 (lb/cu ft g/m3)
	pound per cubic yard	lb/yd3		lb/cu yd		1.0 lb/cu yd (0.59 kg/m3)	lb/yd3 kg/m3 (lb/cuyd kg/m3) lb/yd3 g/m3 (lb/cuyd g/m3)
ENERGY (Full list)
system	unit	unit- code		abbrev- iation	notes	sample default conversion	combination output units
SI	gigajoule	GJ		GJ		1.0 GJ (280 kWh)
	megajoule	MJ		MJ		1.0 MJ (0.28 kWh)
	kilojoule	kJ		kJ		1.0 kJ (240 cal)
	hectojoule	hJ		hJ		1.0 hJ (24 cal)
	decajoule	daJ		daJ		1.0 daJ (2.4 cal)
	joule	J		J		1.0 J (0.24 cal)
	decijoule	dJ		dJ		1.0 dJ (0.024 cal)
	centijoule	cJ		cJ		1.0 cJ (0.0024 cal)
	millijoule	mJ		mJ		1.0 mJ (0.00024 cal)
	microjoule	μJ (uJ)		μJ		1.0 μJ (2.4×10−7 cal)
	nanojoule	nJ		nJ		1.0 nJ (2.4×10−10 cal)
cgs	megaerg	Merg		Merg		1.0 Merg (0.10 J)
	kiloerg	kerg		kerg		1.0 kerg (0.10 mJ)
	erg	erg		(none)		1.0 erg (0.10 μJ)
Watt-hour multiples	terawatt-hour	TWh		TWh		1.0 TWh (3.6 PJ)
		TW.h		TW⋅h
	gigawatt-hour	GWh		GWh		1.0 GWh (3.6 TJ)
		GW.h		GW⋅h
	megawatt-hour	MWh		MWh		1.0 MWh (3.6 GJ)
		MW.h		MW⋅h
	kilowatt-hour	kWh		kWh		1.0 kWh (3.6 MJ)
		kW.h		kW⋅h
	watt-hour	Wh		Wh		1.0 Wh (3.6 kJ)
		W.h		W⋅h
Electron- volt multiples
	gigaelectronvolt	GeV		GeV		1.0 GeV (0.16 nJ)
	megaelectronvolt	MeV		MeV		1.0 MeV (0.16 pJ)
	kiloelectronvolt	keV		keV		1.0 keV (0.16 fJ)
	electronvolt	eV		eV		1.0 eV (0.16 aJ)
	millielectronvolt	meV		meV		1.0 meV (0.16 zJ)
Calorie multiples	calorie	Cal		Cal	The thermo-chemical calorie is the default definition. For others, see the full list.	1.0 Cal (4.2 kJ)
	megacalorie	Mcal		Mcal		1.0 Mcal (4.2 MJ)
	kilocalorie	kcal		kcal		1.0 kcal (4.2 kJ)
	calorie	cal		cal		1.0 cal (4.2 J)
	millicalorie	mcal		mcal		1.0 mcal (4.2 mJ)
pound/ ounce-foot/ inch-hour-minute-second	foot-poundal	ftpdl		ft⋅pdl		1.0 ft⋅pdl (0.042 J)
	foot-pound force	ftlbf		ft⋅lbf		1.0 ft⋅lbf (1.4 J)
		ftlb-f		ft⋅lbf
	inch-pound force	inlbf		in⋅lbf		1.0 in⋅lbf (110 mJ)
		inlb-f		in⋅lbf
	inch-ounce force	inozf		in⋅ozf		1.0 in⋅ozf (7.1 mJ)
		inoz-f		in⋅ozf
	horsepower-hour	hph		hp⋅h		1.0 hp⋅h (0.75 kWh)
British thermal unit	British thermal unit	Btu		Btu	The International Steam Table British thermal unit is used. For others, see the full list.	1.0 Btu (1.1 kJ)
		BTU		BTU
TNT-based units	gigatonne of TNT	GtTNT		(none)		1.0 gigatonne of TNT (4.2 EJ)
	gigaton of TNT	GtonTNT		(none)
	megatonne of TNT	MtTNT		(none)		1.0 megatonne of TNT (4.2 PJ)
	megaton of TNT	MtonTNT		Mt
	kilotonne of TNT	ktTNT		(none)		1.0 kilotonne of TNT (4.2 TJ)
	kiloton of TNT	ktonTNT		kt
	tonne of TNT	tTNT		(none)		1.0 tonne of TNT (4.2 GJ)
	ton of TNT	tonTNT		(none)
Other
	Hartree	Eh		Eh		1.0 Eh (27 eV)
	rydberg	Ry		Ry		1.0 Ry (14 eV)
	tonne of oil equivalent	toe		toe		1.0 toe (42 GJ)
	barrel of oil equivalent	BOE		BOE		1.0 BOE (6.1 GJ)
	cubic foot of natural gas	cuftnaturalgas (cufootnaturalgas)			Unit-code cufootnaturalgas will show "cubic foot of natural gas" if plural.	1.0 cubic foot of natural gas (1.1 MJ)
	latm	latm		(none)		1.0 latm
		Latm		Latm
	impgalatm	impgalatm		(none)		1.0 impgalatm
	USgalatm	USgalatm (usgalatm)		(none)		1.0 USgalatm
		U.S.galatm (usgalatm)		U.S.galatm
FORCE (Full list)
system	unit	unit- code		abbrev- iation	notes	sample default conversion	combination output units
SI	giganewton	GN		GN	Allows triple output units. See: full list.	1.0 GN (220,000,000 lbf)	GN LT-f GN LTf GN ST-f GN STf
	meganewton	MN		MN	Allows triple output units. See: full list.	1.0 MN (220,000 lbf)	MN LT-f MN LTf MN ST-f MN STf
	kilonewton	kN		kN	Allows triple output units. See: full list.	1.0 kN (220 lbf)	kN LT-f kN LTf kN ST-f kN STf
	newton	N		N		1.0 N (0.22 lbf)	N lb-f N lbf N oz-f N ozf
	millinewton	mN		mN		1.0 mN (0.0036 ozf)	mN oz-f mN ozf mN gr-f mN grf
	micronewton	μN (uN)		μN		1.0 μN (0.0016 grf)	μN gr-f μN grf
	nanonewton	nN		nN		1.0 nN (1.6×10−6 grf)	nN gr-f nN grf
cgs	megadyne	Mdyn		Mdyn		1.0 Mdyn (2.2 lbf)
	kilodyne	kdyn		kdyn		1.0 kdyn (0.036 ozf)
	dyne	dyn (dyne)		dyn		1.0 dyn (0.016 grf)
	millidyne	mdyn		mdyn		1.0 mdyn (1.6×10−5 grf)
Metric gravitational units	tonne-force	t-f		tf		1.0 tf (9.8 kN; 0.98 LTf; 1.1 STf)
		tf		tf
	kilogram-force	kg-f		kgf		1.0 kgf (9.8 N; 2.2 lbf)
		kgf		kgf
	gram-force	g-f		gf		1.0 gf (9.8 mN; 0.035 ozf)
		gf		gf
	milligram-force	mg-f		mgf		1.0 mgf (9.8 μN; 0.015 grf)
		mgf		mgf
Avoirdupois-based units	poundal	pdl		pdl		1.0 pdl (0.14 N)
	long ton-force	LT-f		LTf		1.0 LTf (10.0 kN)	LT-f ST-f
		LTf		long ton-force			LTf STf
	short ton-force	ST-f		STf		1.0 STf (8.9 kN)	ST-f LT-f
		STf		short ton-force			STf LTf
	pound-force	lb-f		lbf		1.0 lbf (4.4 N)
		lbf		lbf
	grain-force	gr-f		grf		1.0 grf (640 μN)
		grf		grf
LENGTH (Full list)
system	unit	unit- code		abbrev- iation	notes	sample default conversion	combination output units
SI	megametre	Mm		Mm	US spelling: megameter	1.0 Mm (620 mi)
	kilometre	km		km	US spelling: kilometer	1.0 km (0.62 mi)	km mi
	metre	m		m	US spelling: meter	1.0 m (3 ft 3 in)	m ft m ftin
	centimetre	cm		cm	US spelling: centimeter	1.0 cm (0.39 in)	cm in
	millimetre	mm		mm	US spelling: millimeter	1.0 mm (0.039 in)	mm in
	micrometre	μm (um)		μm	US spelling: micrometer	1.0 μm (3.9×10−5 in)
	nanometre	nm		nm	US spelling: nanometer	1.0 nm (3.9×10−8 in)
non-SI metric	ångström	Å (angstrom)		Å		1.0 Å (3.9×10−9 in)
Imperial & US customary	mile	mi		mi		1.0 mi (1.6 km)	mi km
	furlong	furlong		(none)		1.0 furlong (660 ft; 200 m)
	chain	chain		(none)		1.0 chain (66 ft; 20 m)
	rod	rd		rd	For other names of this unit see the full list.	1.0 rd (17 ft; 5.0 m)
	fathom	fathom		(none)	fathom ≡ 6 ft	1.0 fathom (6.0 ft; 1.8 m)
	yard	yd		yd	assumes the international definition	1.0 yd (0.91 m)
	foot	ft (foot)		ft	long code "foot" outputs foot (and never feet)	1.0 ft (0.30 m)	ftin (feet and inches) ft m (foot m)
	inch	in		in		1.0 in (25 mm)	in cm in mm
Other	nautical mile	nmi		nmi	the international standard nautical mile For other nautical miles see the full list.	1.0 nmi (1.9 km; 1.2 mi)
	parsec	pc		pc		1.0 pc (3.3 ly)
	light-year	ly		ly		1.0 ly (63,000 AU)
	astronomical unit	AU		AU		1.0 AU (150,000,000 km; 93,000,000 mi)
MASS (Full list)
system	unit	unit- code		abbrev- iation	notes	sample default conversion	combination output units
SI	kilogram	kg		kg	Allows triple output units. See: full list.	1.0 kg (2.2 lb)	kg lb kg st
	gram	g		g		1.0 g (0.035 oz)	g oz
	milligram	mg		mg		1.0 mg (0.015 gr)	mg gr
	microgram	μg (ug)		μg		1.0 μg (1.5×10−5 gr)
non-SI metric	tonne	t		t	Allows triple output units. See: full list.	1.0 t (0.98 long tons; 1.1 short tons)	t LT t ST
	metric ton	MT		t			MT LT MT ST
Avoirdupois	long ton	LT		(none)	2,240 lb used mostly in the British Commonwealth. Allows triple output units. See: full list.	1.0 long ton (1.0 t)	LT t LT MT LT ST
		long ton		long ton
	short ton	ST		(none)	2,000 lb used mostly in the US. Allows triple output units. See: full list.	1.0 short ton (0.91 t)	ST t ST MT ST LT
		short ton		short ton
	stone	st		st	14 lb used mostly in the British Commonwealth except Canada. Allows triple output units. See: full list.	1.0 st (14 lb; 6.4 kg)	st kg st lb
	pound	lb		lb	Allows triple output units. See: full list.	1.0 lb (0.45 kg)	lb kg lb st
	ounce	oz		oz		1.0 oz (28 g)	oz g
	drachm	drachm		(none)		1.0 drachm (1.8 g)
	drachm	dram		(none)
	grain	gr		gr	equivalent to the troy grain	1.0 gr (0.065 g)
Troy	troy ounce	ozt		ozt		1.0 ozt (1.1 oz; 31 g)
other	carat	carat		(none)		1.0 carat (0.20 g)
SPEED (Full list)
system	unit	unit- code		abbrev- iation	notes	sample default conversion	combination output units
SI	metre per second	m/s		m/s	US spelling: meter per second	1.0 m/s (3.3 ft/s)	m/s ft/s (m/s foot/s)
non-SI metric	kilometre per hour	km/h		km/h	US spelling: kilometer per hour	1.0 km/h (0.62 mph)	km/h mph
Imperial & US customary	mile per hour	mph		mph		1.0 mph (1.6 km/h)	mph km/h mph kn
	foot per second	ft/s (foot/s)		ft/s	long code "foot/s" outputs foot per second (and never feet)	1.0 ft/s (0.30 m/s)	ft/s m/s
Maritime units	knot	kn (knot)		kn		1.0 kn (1.9 km/h; 1.2 mph)	kn mph
TEMPERATURE (Full list)
system	unit	unit- code		abbrev- iation	notes	sample default conversion	combination output units
SI	K	K		K	Allows triple output units. See: full list.	1.0 K (−272.15 °C; −457.87 °F)	K °C (K C) K °R (K R) K °F (K F)
	°C	°C (C)		°C		1.0 °C (33.8 °F)	°C K (C K) °C °R (C R) °C °F (C F)
Imperial & US customary	°R	°R (R)		°R		1.0 °R (0.556 K; −458.670 °F; −272.594 °C)	°R K (R K) °R °C (R C) °R °F (R F)
	°F	°F (F)		°F		1.0 °F (−17.2 °C)	°F K (F K) °F °C (F C) °F °R (F R)
	Celsius change	C-change			Used for temperature intervals instead of actual temperatures Example:  {{convert|5|C-change|0}} warmer Result: 5 °C (9 °F) warmer
	Fahrenheit change	F-change			Used for temperature intervals instead of actual temperatures Example:  {{convert|10|F-change|0}} colder Result: 10 °F (6 °C) colder
TORQUE (Full list)
system	unit	unit- code		abbrev- iation	notes	sample default conversion	combination output units
Industrial
SI	newton-metre	Nm		N⋅m	Triple combinations are also possible. See the full list.	1.0 N⋅m (0.74 lbf⋅ft)	Nm kg.m Nm lb.ft
Non-SI metric	kilogram metre	kg.m		kg⋅m		1.0 kg⋅m (9.8 N⋅m; 7.2 lb⋅ft)	kg.m Nm kg.m lb.ft
Imperial & US customary	pound force-foot	lb.ft		lb⋅ft		1.0 lb⋅ft (1.4 N⋅m)	lb.ft Nm lb.ft kg-m
Scientific
SI	newton-metre	N.m		N⋅m	Triple combinations are also possible. See the full list.	1.0 N⋅m (0.74 lbf⋅ft)	N.m kgf.m N.m lbf.ft
Non-SI metric	kilogram force-metre	kgf.m		kgf⋅m		1.0 kgf⋅m (9.8 N⋅m; 7.2 lbf⋅ft)	kgf.m N.m kgf.m lbf.ft
Imperial & US customary	pound force-foot	lbf.ft		lbf⋅ft		1.0 lbf⋅ft (1.4 N⋅m)	lbf.ft N.m lbf.ft kgf.m
VOLUME (Full list)
system	unit	unit- code		abbrev- iation	notes	sample default conversion	combination output units
SI	cubic metre	m3		m3	US spelling: cubic meter one kilolitre	1.0 m3 (35 cu ft)
	cubic centimetre	cm3		cm3	US spelling: cubic centimeter one millilitre	1.0 cm3 (0.061 cu in)
		cc		cc
	cubic millimetre	mm3		mm3	US spelling: cubic millimeter	1.0 mm3 (6.1×10−5 cu in)
non-SI metric	kilolitre	kl		kl	US spelling: kiloliter one cubic metre	1.0 kl (35 cu ft)
		kL		kL
	litre	l		l	US spelling: liter one cubic decimetre Allows triple output units. See: full list.	1.0 l (0.22 imp gal; 0.26 US gal)	l impgal l USgal l U.S.gal l USdrygal l U.S.drygal
		L		L			L impgal L impqt L USgal L U.S.gal L USdrygal L U.S.drygal
	centilitre	cl		cl	US spelling: centiliter	1.0 cl (0.35 imp fl oz; 0.34 US fl oz)
		cL		cL
	millilitre	ml		ml	US spelling: milliliter one cubic centimetre	1.0 ml (0.035 imp fl oz; 0.034 US fl oz)	ml impoz ml USoz ml U.S.oz
		mL		mL			mL impoz mL USoz mL U.S.oz
Imperial & US customary	cubic yard	cuyd		cu yd		1.0 cu yd (0.76 m3)
	cubic foot	cuft (cufoot)		cu ft	long code "cufoot" outputs cubic foot (and never feet)	1.0 cu ft (0.028 m3)
	cubic inch	cuin		cu in		1.0 cu in (16 cm3)
Imperial	imperial barrel	impbbl		imp bbl	36 imp gal	1.0 imp bbl (160 l; 36 imp gal; 43 US gal)
	imperial bushel	impbsh		imp bsh	8 imp gal	1.0 imp bsh (36 l; 8.0 imp gal; 8.3 US dry gal)
		impbu		imp bu
	imperial gallon	impgal		imp gal	4.54609 litres by definition, also 4 imp qt or 8 imp pt or 160 imp fl oz Allows triple output units. See: full list.	1.0 imp gal (4.5 l; 1.2 US gal)	impgal l impgal L impgal USgal impgal U.S.gal impgal USdrygal impgal U.S.drygal
	imperial quart	impqt		imp qt	1/4 imp gal or 40 imp fl oz	1.0 imp qt (1,100 ml; 38 US fl oz)
	imperial pint	imppt		imp pt	1/8 imp gal or 20 imp fl oz	1.0 imp pt (0.57 l)
	imperial fluid ounce	impoz (impfloz)		imp fl oz	1/160 imp gal	1.0 imp fl oz (28 ml; 0.96 US fl oz)	impoz USoz impoz U.S.oz impoz ml impoz mL
US customary liquid measure	US barrel	USbbl		US bbl	31½ US gal used for liquids except for oil and beer (see the full list)	1.0 US bbl (120 l; 32 US gal; 26 imp gal)
		U.S.bbl		U.S. bbl
	barrel	oilbbl		bbl	42 US gal	1.0 bbl (0.16 m3)
	US beer barrel	USbeerbbl (usbeerbbl)		US bbl		1.0 US bbl (120 l; 31 US gal; 26 imp gal)
		U.S.beerbbl (usbeerbbl)		U.S. bbl
	US gallon	USgal		US gal	231 cubic inches by definition, also 4 US qt or 8 US pt or 128 US fl oz Allows triple output units. See: full list.	1.0 US gal (3.8 l; 0.83 imp gal)	USgal l USgal L USgal impgal
		U.S.gal		U.S. gal			USgal l USgal L USgal impgal
	US quart	USqt		US qt	1/4 US gal or 32 US fl oz	1.0 US qt (950 ml)
		U.S.qt		U.S. qt
	US pint	USpt		US pt	1/8 US gal or 16 US fl oz	1.0 US pt (0.47 l; 0.83 imp pt)
		U.S.pt		U.S. pt
	US fluid ounce	USoz (USfloz)		US fl oz	1/128 US gal	1.0 US fl oz (30 ml)	USoz ml USoz mL USoz impoz
		U.S.oz (U.S.floz)		U.S. fl oz			U.S.oz ml U.S.oz mL U.S.oz impoz
US customary dry measure	US dry barrel	USdrybbl		US dry bbl	105/32 US bsh	1.0 US dry bbl (0.12 m3)
		U.S.drybbl		U.S. dry bbl
	US bushel	USbsh		US bsh	2150.42 cubic inches by definition	1.0 US bsh (35 l; 8.0 US dry gal; 7.8 imp gal)
		U.S.bsh		U.S. bsh
	US bushel	USbu		US bu	2150.42 cubic inches by definition	1.0 US bu (35 l; 8.0 US dry gal; 7.8 imp gal)
		U.S.bu		U.S. bu
	US dry gallon	USdrygal		US dry gal	1/8 US bsh Allows triple output units. See: full list.	1.0 US dry gal (4.4 l)	USdrygal l USdrygal L USdrygal impgal
		U.S.drygal		U.S. dry gal			U.S.drygal l U.S.drygal L U.S.drygal impgal
	US dry quart	USdryqt		US dry qt	1/32 US bsh	1.0 US dry qt (1,100 ml)
		U.S.dryqt		U.S. dry qt
	US dry pint	USdrypt		US dry pt	1/32 US bsh	1.0 US dry pt (550 ml)
		U.S.drypt		U.S. dry pt
PRESSURE
	unit	unit- code		abbrev- iation		sample default conversion
	gigapascal	GPa		GPa		1.0 GPa (150,000 psi)
	megapascal	MPa		MPa		1.0 MPa (150 psi)
	kilopascal	kPa		kPa		1.0 kPa (0.15 psi)
	hectopascal	hPa		hPa		1.0 hPa (0.015 psi)
	pascal	Pa		Pa		1.0 Pa (0.00015 psi)
	millipascal	mPa		mPa		1.0 mPa (1.5×10−7 psi)
	millibar	mbar		mbar		1.0 mbar (1.0 hPa)
		mb		mb
	decibar	dbar		dbar		1.0 dbar (10 kPa)
	bar	bar		(none)		1.0 bar (100 kPa)
	kilobarye	kBa		kBa		1.0 kBa (1.0 hPa)
	barye	Ba		Ba		1.0 Ba (0.10 Pa)
	standard atmosphere	atm		atm		1.0 atm (100 kPa)
	torr	Torr		Torr		1.0 Torr (0.13 kPa)
	millimetre of mercury	mmHg		mmHg		1.0 mmHg (0.13 kPa)
	inch of mercury	inHg		inHg		1.0 inHg (3.4 kPa)
	pound per square inch	psi		psi		1.0 psi (6.9 kPa)
FUEL EFFICIENCY
	unit	unit- code			notes		combinations
	kilometres per litre	km/l (km/L)			Use km/L to get "km/L"		km/l mpgimp km/l mpgus
	litres per 100 kilometres	l/100 km (L/100 km)			Use L/100 km to get "L/100 km"		l/100 km mpgimp l/100 km mpgus
	litres per kilometre	l/km (L/km)			Use L/km to get "L/km"		l/km impgal/mi l/km usgal/mi
	miles per imperial gallon	mpgimp					mpgimp mpgus
	miles per US gallon	mpgus (mpgUS, mpgU.S.)			Use mpgUS to get "US" Use mpgU.S. to get "U.S." mpgus will give "U.S." if spelling is set to US & "US" otherwise		mpgus mpgimp
	imperial gallons per mile	impgal/mi					impgal/mi
	US gallons per mile	usgal/mi (USgal/mi, U.S.gal/mi)			As above with the us vs US vs U.S.		usgal/mi
The mpgUS, mpgU.S., USgal/mi vs U.S.gal/mi, km/L, L/100 km and L/km variants work within combinations also (making 36 combinations in total).
POPULATION DENSITY
	unit	unit- code			notes		combinations
	inhabitants per square kilometre	PD/km2			PD stands for population density, i.e. humans (inhabitants)		PD/km2 PD/sqmi
	per square kilometre	/km2			Used when the word 'inhabitants' would be inappropriate.		/km2 /sqmi
	inhabitants per hectare	PD/ha					PD/ha PD/acre
	per hectare	/ha					/ha /acre
	inhabitants per square mile	PD/sqmi			PD stands for population density, i.e. humans (inhabitants)		PD/sqmi PD/km2
	per square mile	/sqmi			Used when the word 'inhabitants' would be inappropriate.		/sqmi /km2
	inhabitants per acre	PD/acre					PD/acre PD/ha
	per acre	/acre					/acre /ha
COST PER UNIT MASS
	unit	unit- code			notes		combinations
	dollars per pound	$/lb			"$" can mean US$, HK$, etc.		(none)
	dollars per kilogram	$/kg					(none)
	dollars per troy ounce	$/ozt			12 troy ounces in 1 troy pound		(none)

Parameter list

Parameter options for {{convert}}
Parameter	Value	Description	Note
|abbr	in	Use symbol for first (left-hand side) unit	Unit display
	off	Use name for all units	Unit display
	none
	on	Use symbol for all units	Unit display
	out	Use symbol for right-hand side unit (default)	Unit display
	unit	Use symbol for all units when using scientific notation	Unit display
	values	Omit both the input and output units: show only the numbers	Unit display
	~	Shows both unit name and symbol	Unit display
	mid	User-specified text after the input unit; sets adj=on (adjective). Expects 1 unnamed parameter.	Word adding, adjective
	on	Unit name is adjective (singular and hyphenated)	Grammar, adjective
	pre	User-specified text before input unit. Expects 1 unnamed parameter.	Word adding
	ri0	Round input with precision 0	Input precision
	ri1	Round input with precision 1	Input precision
	ri2	Round input with precision 2	Input precision
	ri3	Round input with precision 3	Input precision
|comma	5	Only use comma for thousands separator if 5 or more digits	Number format
	gaps	Use gaps (space), not comma, for thousands separator	Number format
	off	No thousands separator	Number format
|disp	b	Join input and output using " (...)" (default)	Join values
	sqbr	Join input and output using " [...]"	Join values
	br	Join input and output using "<br/>"	Join values
	comma	Join input and output using ", "	Join values
	or	Join input and output using " or "	Join values
	number	Display output number only	Parts only
	output number only
	out	Display only output number and name/symbol	Parts only
	output only
	preunit	Text to be inserted after value and before units, for both input and output, with optionally different text for output. Expects 1 or 2 unnamed parameters.	Word adding
	table	Output is suitable for a table cell with align="right"	Table columns
	tablecen	Output is suitable for a table cell with align="center"	Table columns
	unit	Display input name/symbol only (not input number, not output)	Parts only
	unit2	Display output name/symbol only (not input; not output number)	Parts only
	x	Join input and output using user-specified text	Word adding
|frac	N	Show imperial number in fractions, denominator=N	Number format, fraction
|input	P2048 (e.g.)	Reads and converts Wikidata property	Inside template
|lk	in	Link left-hand side unit name or symbol	Unit link
	on	Link all unit names or symbols (but not twice for the same unit)	Unit link
	out	Link right-hand side unit name or symbol	Unit link
|order	flip	Inverts order of input, output measurements (conversion first)	Order
	out	Displays output units in the order entered, skipping input unit	Order
|qid	Q1056131 (e.g.)	Reads Wikidata property from Wikidata item	Inside template; testing
|qual	Q613628 (e.g.)	Qualify Wikidata property
|round	5	Rounds calculation to the nearest multiple of 5	Output precision
	25	Rounds calculation to the nearest multiple of 25	Output precision
	each	In a range, each number is rounded by the default rounding	Output precision
|sigfig	N	Round output number to N significant figures (N is a positive integer)	Output precision
|sortable	on	Adds invisible sort key	Table sort
|sp	us	Use U.S. spelling ("meter" instead of default "metre")	Spelling U.S. names
|spell	in	Spell input number in words	Spelling numbers
	In	Spell input number in words with first letter uppercase	Spelling numbers
	on	Spell input and output numbers in words	Spelling numbers
	On	Spell input and output numbers in words with first letter uppercase	Spelling numbers
|$	€	Replace $-sign with a currency sign, for example in $/acre (no currency conversion happens)	Cost per unit
|debug	yes	Debugging only. In a sortable table: show the normally hidden sort key	Table sort
|disp	flip	Deprecated. Use |order=flip	Order
|sing=		Deprecated. Use |adj=	Plurals

Deprecated options

This list: 

Deprecated options should not be used. They may produce incorrect or undesired results and there is no guarantee that they will be supported in the future.

• disp=flip is deprecated. Use order=flip instead
• sing= is deprecated in any situation. Use adj= instead
• Range separator |xx| is deprecated (not MOS compliant). Use |x| instead
• Range separator |*| is deprecated (not MOS compliant). Use |x| instead

TemplateData

This is the TemplateData for this template used by TemplateWizard, VisualEditor and other tools. See a monthly parameter usage report for this template in articles based on this TemplateData.

TemplateData for Convert

Converts measurements to other units.

Template parameters

Parameter		Description	Type	Status
value	1	the value to convert	Number	optional
from unit	2		Line	optional
to units	3	the unit to convert into	Line	optional
precision or suffix	4	significant digits after decimal dot or, if negative, exponent of ten	Number	optional
link units	lk	“on” all, “in” input, “out” output or “off” no units Default off	Line	optional
abbreviation	abbr	display for the units: “on” unit symbols, “off” all unit names in full words, “in” input unit symbol, “out” abbreviated output units, “values” no units at all Default out	Line	optional
spelling	sp	“us” display U.S. spelling of unit names	Line	optional
adjective	adj	adjective form (singular unit name appended by hyphen) “on” or “mid” to put conversion at end	Line	optional
conversion	disp	display conversion result: “or” after ‘or’, “x” with custom prefix and suffix, “b” in parentheses, “table”/“tablecen”, “output only” alone, “output number only” alone and without unit, “unit” not at all but input unit; if the value is a number it is used as precision Default b	Line	optional
ordering	order	“flip” returns converted value first, input value second.	Line	optional
significant figures	sigfig	number that sets the number of significant figures	Number	optional
rounding output	round	“5” rounds the output number to nearest multiple of 5, “25” to nearest multiple of 25, “each” rounds each number in a range	Line	optional
thousands separator	comma	Sets or suppresses thousand separator in the numbers. “off” = no separator; “gaps”: use space not comma; “5” and “gaps5”: only add separator when number > 5 positions (10,000 or more) Default on	Line	optional
sort key	sortable	“on” generates a hidden sort key	Line	optional

See also

• Template:Convert/old — Version as used until December 2013
• Template:Convert/units not supported